Презентация на тему: Tele remote control

Tele remote control
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Connection and drilling with Tele Remote
Tele remote control
Tele remote control
1/13
Средняя оценка: 4.0/5 (всего оценок: 86)
Код скопирован в буфер обмена
Скачать (1810 Кб)
1

Первый слайд презентации: Tele remote control

Connection and drilling with Tele Remote

Изображение слайда
2

Слайд 2: Connection and drilling with Tele Remote

Drilling from the control room Access Point

Изображение слайда
3

Слайд 3: Connection and drilling with Tele Remote

The Control Room's safety system circuit must be initialized. S1 lights off means that the Control Room machine stop has been initialized. Initialize the Control Room's machine stop by pressing button S1. Drilling from the Control Room 3

Изображение слайда
4

Слайд 4: Connection and drilling with Tele Remote

Point the rig's antenna to the access point Make sure that the antenna don't have any visible damage Set up the drill rig for drilling Drilling from the Control Room 4

Изображение слайда
5

Слайд 5: Connection and drilling with Tele Remote

Make sure that the drill rig is within the WiFi network's coverage range. The status light on the switch in the drill rig will flash green. (It takes approx. three minutes for drill rig and control room to establish contact). Press and hold the connection button on the switch for four seconds. The button will now illuminates with a continuous green light. Ensure that the drill rig's operator panel is deallocated and turn the switch D733 to radio remote control. Check that all Status are ok. Drilling from the Control Room 5

Изображение слайда
6

Слайд 6: Connection and drilling with Tele Remote

Tele Remote menu Atlas Copco Machine Server / Operator station Safety system status Area guard left /right Video encoder Information Local mode Remote mode Drilling from the Control Room 6

Изображение слайда
7

Слайд 7: Connection and drilling with Tele Remote

Requirements for tele-remote operation All equipment in the control room must be started up and communication between drill rig and control room must be operative. The control room's machine stop circuit must be initiated Emergency stop on the drill rig must not be activated. The drill rig's area guard must not be triggered. The drill rig's operator panel must be deallocated. Drilling from the Control Room 7

Изображение слайда
8

Слайд 8: Connection and drilling with Tele Remote

Local mode The screen in the control room display D509 will have an empty “Rig info” box Remote mode The screen in the control room display D509 will change appearance to a filled “Rig info” box Drilling from the Control Room 8

Изображение слайда
9

Слайд 9: Connection and drilling with Tele Remote

Select the drill rig to be allocated by highlighting its name in the remote operator panel's main menu. Press the remote control button on the remote operator panel's right-hand keypad. Tele remote” symbol will change from grey to green The symbol for hydraulic pumps started turn into “0” The video display will start to show a video stream from the rig Camera joystick and camera button are now activated Press”Pump start” button The symbol for hydraulic pumps started turn into “I” Drilling can now be started Drilling works in the same way as on the drill rig operator panel Allocate drill rig to remote operator panel 9

Изображение слайда
10

Слайд 10: Connection and drilling with Tele Remote

Allocate drill rig to remote operator panel 10 Joystick movements Camera movements Front Camera down Rear Camera up Right Camera right Left Camera left Camera left Zoom in/out Button push Result Depress and release camera button Changes active camera Depress the camera button for one second Active camera's wiper sweeps once Hold the camera button depressed for longer than one second Active camera's wiper runs until the button is released Camera button

Изображение слайда
11

Слайд 11: Connection and drilling with Tele Remote

Conditions for allocation of remote operator panel The joysticks must be calibrated, fault- free and in the centre position. The control room must have stable contact with the drill rig. The drill rig must not be allocated by another operator panel. The program version must be the same on control room and drill rig. Allocate drill rig to remote operator panel 11

Изображение слайда
12

Слайд 12

Изображение слайда
13

Последний слайд презентации: Tele remote control

Изображение слайда